Why a bar of the right length may not fit: bar mounts
A guide bar can be the right length, pitch and gauge and still not bolt onto your saw. The part that decides this is the mount: the shape of the bar’s tail and the slot and holes cut into it. This page covers what the makers’ documents say about mounts, how each maker labels them, and how to check a replacement bar before you buy it.
What a mount consists of
Stihl defines the tail of a bar by three things: the position of the slot for the mounting studs, the position of the oil inlet holes, and the fixing holes for the chain tensioner. Husqvarna’s operator’s manual makes the same point in one line: the chain oil hole and the hole for the chain tensioner must align with the saw. Oregon’s manual names the same parts on its bars as the tail, the oil hole and the adjustment hole.
Each part has a job. The mounting studs pass through the slot. The saw’s adjustment pin sits in the tensioner hole, which is how the tensioner moves the bar. Oil reaches the bar groove through the oil inlet hole. All three have to line up with the saw, not only the slot.
Four things define a bar
Stihl lists four characteristics that define a guide bar. A replacement has to match the saw and the chain on all four.
- Groove width. It must match the drive link gauge of the chain.
- Nose sprocket. On a sprocket-nose bar, the pitch of the nose sprocket must be the same as the pitch of the chain and of the saw’s drive sprocket.
- Bar tail. The mount described above.
- Cutting length. Stihl ties it to the job: the log diameter the bar can cut.
Oregon measures cutting length, which it also names the called length, from the front of the saw to the tip of the bar, rounded to the nearest inch. The tail sits inside the saw, so the bar is longer than its name: Oregon notes that a 16 inch bar may be about 20 inches overall. Two bars with the same called length and different tails are different parts.
How makers label mounts
Oregon
Oregon gives every mount a four-character code, such as A041, A074, D025 or K095. The code is the last part of the bar’s part number, and Oregon’s product pages show it as “Tail Mount”. For each code, Oregon’s manual lists the saw brands it is used on. Three points from those lists matter when you shop:
- A brand is not a mount. Husqvarna appears under A041, A095, K041, K095 and D009. Stihl appears under A074, D025 and E031. Echo appears under K216, D096, D176 and D196. Knowing the brand of your saw does not tell you which bar tail it takes.
- A mount is not a brand. Oregon lists A041 for more than a dozen brands, from Craftsman and Homelite to Husqvarna and Poulan.
- The first letter can change with the drive-link count. Where two bars would have the same length in their part numbers but take different drive-link counts, Oregon marks one with a Z, for example K095 and Z095.
Codes that begin with T, such as T041, are Intenz mounts. An Intenz bar has the chain tensioner built into the bar. Oregon states that saws built or adapted for an Intenz bar have no adjustment pin of their own, and that only an Intenz bar should replace an Intenz bar.
Husqvarna
Husqvarna sorts its bars and saws into two groups, small bar mount and large bar mount. Its US bar listings put the group in the product name, and give a “Bar mount type” code in the specifications: HSM on a small-mount bar and HLM on a large-mount bar.
Stihl
The Stihl documents read for this page describe the bar tail but give no name or code for mount types. What Stihl does provide is a data block etched on the tail of every bar, starting with the bar’s part number, and a list of bars for each saw in the specifications chapter of that saw’s instruction manual.
Reading an Oregon bar number
Oregon’s bar part numbers have 10 or 11 characters and are etched on the bar body. Oregon’s own example is 18 0 EXL D K095.
| Part | In 180EXLDK095 | Meaning |
|---|---|---|
| Length | 18 | Called length in inches |
| Gauge | 0 | 4 = .043″, 0 = .050″, 8 = .058″, 3 = .063″ |
| Type | EXL | Bar family and nose type. EXL is a PowerCut bar with a replaceable sprocket nose; SD is a Single Rivet sprocket-nose bar; DXL is a DuraCut solid-nose bar. |
| Nose | D | Pitch and tooth count of the nose sprocket. A = 1/4″; B or G = .325″; D or H = 3/8″; E = 3/8″ Low Profile; F = .404″; N = .325″ Low Profile. On a solid-nose bar, M = medium nose. |
| Mount | K095 | Tail mount |
Oregon notes two exceptions: its Sculptor carving bars do not follow this system, and PowerCut solid-body bars may be stamped with XXX, ZZZ or other letters because different noses can be fitted to one body.
How to check a replacement bar
- Start from the saw maker’s list. The saw’s manual lists the bars the maker specifies for it. Husqvarna says replacing a bar with a recommended combination is necessary to keep the saw’s safety functions. Stihl says to use only the bar lengths listed in the specifications chapter of the saw’s instruction manual.
- Read the old bar. The part number and data on its tail identify it. How to find your chain size shows what each maker puts there.
- Match the mount by its label. For an Oregon bar, match the tail mount code. For a Husqvarna bar, match small or large mount. Then compare the new bar with the old one, tail on tail: slot, tensioner holes and oil holes should sit in the same places.
- Match pitch and gauge. The groove width must equal the chain gauge, and the nose sprocket pitch must equal the pitch of the chain and the drive sprocket. A narrow-kerf bar is a further restriction: Oregon and Husqvarna both pair narrow-kerf chain with a matching bar.
- Check the tensioner type. If the saw has an Intenz bar, replace it with an Intenz bar.
- Check the nose size. Husqvarna’s manual gives a maximum nose radius for each bar length, stated as a tooth count such as 10T on sprocket-nose bars, and allows a smaller radius than listed but not a larger one.
- Get the drive-link count for the new bar. Oregon warns that a bar from one maker may take a different drive-link count than another maker’s bar of the same length. Use the count given for the bar you are buying, not the count of your old chain.
The bars documented for a particular saw are on its page, for example Echo CS-590 Timber Wolf or Husqvarna 460 Rancher.
What this page leaves out
This page gives no slot widths, stud spacings or hole positions for any mount. The documents it relies on identify mounts by code and by brand, and no dimension could be read from them and quoted. If you need one, measure the bar that came off the saw or ask the bar maker.
Sources
- Oregon, Maintenance and Safety Manual: Saw Chain, Guide Bar and Drive Sprocket (A106971 rev. AC), sections “Guide Bar Terms”, “Using the Guide Bar Number System” and “Chainsaw Mounts”.
- Oregon, Replacing Chainsaw Bars and How to Replace Chainsaw Chain (product support articles).
- Oregon, 180SDEA041 guide bar product page.
- Stihl, Sharpening STIHL Saw Chains (0457 181 0121, 2012), chapter “Determining the Correct Cutting Attachment”.
- Stihl USA, Chain Saw Safety Manual.
- Husqvarna, Operator’s manual 445 II, 445e II, 450 II, 450e II (2021-06).
- Husqvarna US, bar product pages X-FORCE XF-250 (small mount) and X-FORCE XF-388 (large mount).
- Husqvarna, X-CUT saw chain brochure (2016), bars and chains chart.
- Husqvarna UK, Choosing the right chainsaw chain type: A step-by-step guide (Pixel bars).