How to find your chainsaw chain size
Links marked “(paid link)” go to Amazon and earn this site a commission if you buy. As an Amazon Associate I earn from qualifying purchases. How this works
A replacement chain has to match three numbers: pitch, gauge and the number of drive links. All three can usually be read from the bar or the old chain. When the stamps have worn away you can measure them. Bar length is not one of the three, and the last two sections explain why.
The three numbers
- Pitch is the size of the chain. Oregon, Stihl and Husqvarna define it the same way: the distance across three consecutive rivets, divided by two. Oregon lists six pitches for its own chain: 1/4″, .325″ Low Profile, 3/8″ Low Profile, .325″, 3/8″ and .404″. The chain, the drive sprocket and the sprocket in the bar nose must all have the same pitch.
- Gauge is the thickness of the drive link where it sits in the bar groove. It must match the groove width of the bar. Oregon gives the standard gauges as .043″ (1.1 mm), .050″ (1.3 mm), .058″ (1.5 mm) and .063″ (1.6 mm).
- Drive-link count is how chain length is stated. Stihl puts it plainly: the length of the chain is expressed as the number of drive links.
Read the bar first
The tail of the bar, the end that bolts to the saw, usually carries the numbers. Part of the tail sits under the sprocket cover, so you may have to take the cover off to read it. What you find depends on who made the bar.
| Bar maker | Where to look | What it tells you |
|---|---|---|
| Stihl | A laser-etched block on the tail of every Stihl bar | In this order: part number, cutting length, groove width (gauge), number of drive links, and chain pitch on Rollomatic bars only |
| Oregon | A 10 or 11 character part number etched on the bar body at the motor end | The first two digits are the length in inches; the third digit is a gauge code (4 = .043″, 0 = .050″, 8 = .058″, 3 = .063″). The number does not state a drive-link count. |
| Husqvarna | The side plate of the bar; the operator’s manual says the length is usually at the rear end | Husqvarna’s US support article says pitch, gauge and chain length are often printed there. Its chain-selection article says the drive-link count is normally not printed anywhere. If you cannot find it, count the links on the old chain. |
The rest of an Oregon bar number is decoded in the guide to bar mounts.
Then read the chain
- Oregon stamps a number such as 72 or 91 on the drive links. That number stands for one pitch and one gauge.
- Stihl stamps a pitch code digit on each cutter beside the depth gauge, and the last digit of the gauge in millimetres on every drive link.
The tables for both makers are in how to read chain numbers. One stamp is easy to misread: Oregon says most of its chains carry a number such as 025 on each depth gauge. That is the depth gauge setting in thousandths of an inch, not a chain size.
When the stamps are gone
You need a caliper or a ruler marked in millimetres. Search for digital caliper: Amazon.com (paid link) Amazon.ca
Measure pitch
Measure from the centre of one rivet to the centre of the next but one, and divide by two. Stihl explains why you measure across three rivets instead of two: the rivet spacing on a drive link may differ from the spacing on a cutter or tie strap. Compare your result with the figures Stihl prints in its instruction manuals.
| Pitch | Stihl’s figure | Across three rivets |
|---|---|---|
| 1/4″ and 1/4″ P | 6.35 mm | 12.70 mm |
| .325″ | 8.25 mm | 16.50 mm |
| 3/8″ and 3/8″ P | 9.32 mm | 18.64 mm |
| .404″ | 10.26 mm | 20.52 mm |
A measurement cannot tell 3/8″ from 3/8″ P, or 1/4″ from 1/4″ P. The table shows why: they have the same figure. Stihl states that these pairs look very similar but are entirely different pitches and are not interchangeable. What sets the low-profile versions apart is covered in chain types and file sizes. If a stamp survives anywhere on the chain, use it to settle the question. Husqvarna’s own advice, when the pitch cannot be read from the bar, is to have a dealer measure the old chain because it is tricky to do accurately.
Measure gauge
Measure the thickness of a drive link on the lower part, the part that rides in the groove, and compare it with the four standard gauges. Treat the result with care. Oregon warns that normal wear makes it hard to measure gauge accurately on a worn chain, and tells buyers to order by the number stamped on the drive link instead. If the chain is worn and unmarked, look for the gauge on the bar, or take both to a dealer.
Count the drive links
Drive links are the teeth on the inside of the loop that run in the bar groove. Take the chain off, mark one link, and count them all. Do not count cutters. Oregon suggests writing the number down somewhere you will find it again; its chain boxes also have the count stamped on the flap.
Why bar length alone is not enough
- The length on the label is not a measurement of the chain. Oregon defines bar length as the cutting length, also named the called length: the distance from the front of the saw to the bar tip, rounded to the nearest inch. The bar itself is longer; Oregon notes that a 16 inch bar may be about 20 inches overall.
- One length can need two different chains. A Husqvarna operator’s manual lists drive-link counts of 78 and 80 for 20 inch bars and tells owners to check the bar. Oregon uses a different mount code (Z095 in place of K095) to separate bars with the same length in the part number but different drive-link counts.
- One length comes in several pitches and gauges. The same Husqvarna manual lists the same five bar lengths in both .050″ and .058″ gauge. A Stihl manual lists the same cutting lengths with 1.3 mm and 1.6 mm groove widths, and in two pitches.
- Bar makers differ. Oregon warns that the drive-link count depends on the bar’s overall size, which varies by manufacturer, and that an Oregon bar may take a different count than another brand’s bar of the same length.
When the bar on the saw is not the original
A saw page on this site lists what the maker’s documents give for the saw as it was sold, for example Stihl MS 250 or Husqvarna 450 Rancher. If a previous owner fitted a different bar, those numbers may no longer describe your saw. Go by the bar that is on it.
- Read the gauge from the bar that is fitted, using the table above.
- Count the drive links on the chain that currently runs on that bar. This is the step that catches a bar from another maker.
- Confirm the pitch at the saw as well as on the bar. Stihl stamps the pitch and the number of teeth on the chain sprocket, and both Stihl and Oregon require the chain, sprocket and bar nose to share one pitch. If the pitch on the bar and the pitch on the sprocket differ, the parts do not match, and no chain will put that right.
- If the three numbers you find differ from the saw page, order by what you found. How the saw pages are verified explains what those pages can and cannot tell you.
Sources
- Oregon, Maintenance and Safety Manual: Saw Chain, Guide Bar and Drive Sprocket (A106971 rev. AC).
- Oregon, Finding the Right Saw Chain, How to Replace Chainsaw Chain and Replacing Chainsaw Bars (product support articles).
- Oregon, 20BPX066G product page (definitions of pitch, gauge and drive links).
- Stihl, Sharpening STIHL Saw Chains (0457 181 0121, 2012).
- Stihl, MS 231, 251 Instruction Manual (0458-737-8321-C).
- Stihl UK, How to Choose The Right Saw Chain For Your Chainsaw.
- Husqvarna, Operator’s manual 445 II, 445e II, 450 II, 450e II (2021-06).
- Husqvarna US Help Center, Difference in chain size explained (KA-01542).
- Husqvarna Canada, Choosing the right chainsaw chain: A few tips.