Husqvarna 450 Rancher chain size
The 450 Rancher takes .325 inch pitch chain on 13 to 20 inch bars, and Husqvarna's manuals list it in two gauges, .050 (1.3 mm) and .058 (1.5 mm). The trap is the 20 inch bar: the current manual gives 78/80 links and says two different counts exist, an earlier North American edition gave 78 only, and Husqvarna's own 20 inch X-Force bar is an 80 link bar. Shorter bars are unambiguous: 56, 64, 66 and 72 links for 13, 15, 16 and 18 inches.
Husqvarna 450 Rancher, 18-inch bar, .050" (1.3 mm) bar: .325" pitch, .050" gauge, 72 drive links. Other versions of this saw take a different chain. Check which one you have below.
Which version do you have?
Bar groove gauge One source
- .050" (1.3 mm) bar
- .058" (1.5 mm) bar
How to tell: Read the gauge marked on the guide bar (1.3 mm / .050 or 1.5 mm / .058), normally stamped near the mounting end with the bar length. If it is unreadable, look up the number stamped on the old chain's drive links; chain makers code the gauge into that number.[1][2]
Drive-link count of the 20 inch bar One source
- 20 inch bar marked 78 drive links
- 20 inch bar marked 80 drive links
How to tell: Read the drive-link count printed on the 20 inch guide bar (Husqvarna's manual says to check the information on the bar), or count the drive links on the chain that came off it. Bars of 13 to 18 inches are not affected.[1][3]
Husqvarna 450 Rancher chain size by bar length
Links marked “(paid link)” go to Amazon and earn this site a commission if you buy. As an Amazon Associate I earn from qualifying purchases. How this works
| Bar | Applies to | Pitch | Gauge | Drive links | Status |
|---|---|---|---|---|---|
| 13″ (33 cm) | .050" (1.3 mm) bar | .325"[1][2][3] | .050"[1][2][3] | 56[1][2][3][4][5] | One source |
| 13″ (33 cm) | .058" (1.5 mm) bar | .325"[1][2][3] | .058"[1][2][3] | 56[1][2][3] | One source |
| 15″ (38 cm) | .050" (1.3 mm) bar | .325"[1][2][3] | .050"[1][2][3] | 64[1][2][3] | One source |
| 15″ (38 cm) | .058" (1.5 mm) bar | .325"[1][2][3] | .058"[1][2][3] | 64[1][2][3] | One source |
| 16″ (41 cm) | .050" (1.3 mm) bar | .325"[1][2][3] | .050"[1][2][3] | 66[1][2][3][4][5] | One source |
| 16″ (41 cm) | .058" (1.5 mm) bar | .325"[1][2][3] | .058"[1][2][3] | 66[1][2][3] | One source |
| 18″ (46 cm) stock | .050" (1.3 mm) bar | .325"[1][2][3][10] | .050"[1][2][3] | 72[1][2][3][4][5] | One source |
| 18″ (46 cm) | .058" (1.5 mm) bar | .325"[1][2][3] | .058"[1][2][3] | 72[1][2][3] | One source |
| 20″ (51 cm) | .050" (1.3 mm) bar; 20 inch bar marked 78 drive links | .325"[1][2][3] | .050"[1][2][3] | 78[1][2][3][4] | One source |
| 20″ (51 cm) | .050" (1.3 mm) bar; 20 inch bar marked 80 drive links | .325"[1][3] | .050"[1][3] | 80[1][3][4][5] | One source |
| 20″ (51 cm) | .058" (1.5 mm) bar; 20 inch bar marked 78 drive links | .325"[1][2][3] | .058"[1][2][3] | 78[1][2][3] | One source |
| 20″ (51 cm) | .058" (1.5 mm) bar; 20 inch bar marked 80 drive links | .325"[1][3] | .058"[1][3] | 80[1][3] | One source |
Numbers in brackets point to the sources at the foot of the page. “Verified” means two or more separate documents agree and at least one comes from a manufacturer. “One source” means a single manufacturer document; two editions of the same manual count as one. Rows where sources disagree carry no shopping link.
Chains for each set-up
13-inch bar — .050" (1.3 mm) bar
.325" pitch, .050" gauge, 56 drive links One source
| Chain | Part number | Why it is listed |
|---|---|---|
| Husqvarna X-Cut SP33G | 581 64 36-56[4] One source | The saw maker’s own chain |
Other saws that take a chain with .325" pitch, .050" gauge, 56 drive links
Show the evidence for this row
- Pitch:
13 | 0.325 | 0.050 | 10T | 56
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.050 block (first of its gauge), row 13 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Pitch:
13 | 0.325 | 0.050 | 10T | 56
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.050 block (first of its gauge), row 13 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Pitch:
13 | 0.325 | 0.050 | 10T | Husqvarna H30 | 56
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/FR/ES), 1155359-49 Rev.4, 2017-05-03, p. 32, "Guide bar and saw chain combinations" table (models 445 II, 445e II, 450 II, 450e II), 0.050 block, row 13 (cells joined with |) - Gauge:
13 | 0.325 | 0.050 | 10T | 56
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.050 block (first of its gauge), row 13 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Gauge:
13 | 0.325 | 0.050 | 10T | 56
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.050 block (first of its gauge), row 13 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Gauge:
13 | 0.325 | 0.050 | 10T | Husqvarna H30 | 56
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/FR/ES), 1155359-49 Rev.4, 2017-05-03, p. 32, "Guide bar and saw chain combinations" table (models 445 II, 445e II, 450 II, 450e II), 0.050 block, row 13 (cells joined with |) - Drive links:
13 | 0.325 | 0.050 | 10T | 56
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.050 block (first of its gauge), row 13 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Drive links:
13 | 0.325 | 0.050 | 10T | 56
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.050 block (first of its gauge), row 13 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Drive links:
13 | 0.325 | 0.050 | 10T | Husqvarna H30 | 56
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/FR/ES), 1155359-49 Rev.4, 2017-05-03, p. 32, "Guide bar and saw chain combinations" table (models 445 II, 445e II, 450 II, 450e II), 0.050 block, row 13 (cells joined with |) - Drive links:
13" / 56DL | Gauge | .050" | Bar length (inch) | 13 in | Bar length | 33 cm | Drive links | 56 | SKU: 581 64 36-56
— Husqvarna, X-CUT SP33G, .325" pitch, .050 gauge: chain product page (US), Product Options, variant row for SKU 581 64 36-56; the page's "Fits To Model" list includes 450 - Drive links:
13" / 56DL | Bar length (inch) | 13 in | Bar length | 33 cm | Gauge | .050" | SKU: 596 19 97-56
— Husqvarna, X-FORCE Laminate Sprocket Nose, .325" pitch, .050 gauge, small mount (XF-250): bar product page (US), Product Options, variant row for SKU 596 19 97-56; the page's "Fits To Model" list includes 450 - Husqvarna part number:
13" / 56DL | Gauge | .050" | Bar length (inch) | 13 in | Bar length | 33 cm | Drive links | 56 | SKU: 581 64 36-56
— Husqvarna, X-CUT SP33G, .325" pitch, .050 gauge: chain product page (US), Product Options, variant row for SKU 581 64 36-56; the page's "Fits To Model" list includes 450
13-inch bar — .058" (1.5 mm) bar
.325" pitch, .058" gauge, 56 drive links One source
| Chain | Part number | Why it is listed |
|---|---|---|
| Oregon ControlCut 21BPX | 21BPX056G[16] One source | Oregon lists it for this saw |
Show the evidence for this row
- Pitch:
13 | 0.325 | 0.058 | 10T | 56
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.058 block (first of its gauge), row 13 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Pitch:
13 | 0.325 | 0.058 | 10T | 56
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.058 block (first of its gauge), row 13 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Pitch:
13 | 0.325 | 0.058 | 10T | Husqvarna H25 | 56
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/FR/ES), 1155359-49 Rev.4, 2017-05-03, p. 32, "Guide bar and saw chain combinations" table (models 445 II, 445e II, 450 II, 450e II), 0.058 block, row 13 (cells joined with |) - Gauge:
13 | 0.325 | 0.058 | 10T | 56
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.058 block (first of its gauge), row 13 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Gauge:
13 | 0.325 | 0.058 | 10T | 56
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.058 block (first of its gauge), row 13 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Gauge:
13 | 0.325 | 0.058 | 10T | Husqvarna H25 | 56
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/FR/ES), 1155359-49 Rev.4, 2017-05-03, p. 32, "Guide bar and saw chain combinations" table (models 445 II, 445e II, 450 II, 450e II), 0.058 block, row 13 (cells joined with |) - Drive links:
13 | 0.325 | 0.058 | 10T | 56
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.058 block (first of its gauge), row 13 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Drive links:
13 | 0.325 | 0.058 | 10T | 56
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.058 block (first of its gauge), row 13 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Drive links:
13 | 0.325 | 0.058 | 10T | Husqvarna H25 | 56
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/FR/ES), 1155359-49 Rev.4, 2017-05-03, p. 32, "Guide bar and saw chain combinations" table (models 445 II, 445e II, 450 II, 450e II), 0.058 block, row 13 (cells joined with |) - Oregon part number:
ControlCut™ Saw Chain, 13" | Part# 21BPX056G
— Oregon Tool, Inc., Oregon 21BPX056G product page (specifications and Fit Guide), Product heading and Part#; Product Details: "Pitch: .325", gauge: .058", drive link count: 56"; the page's Fit Guide lists Husqvarna "450" (the list is per chain family, not per loop length)
15-inch bar — .050" (1.3 mm) bar
.325" pitch, .050" gauge, 64 drive links One source
| Chain | Part number | Why it is listed |
|---|---|---|
| Oregon PowerCut 20LPX | 20LPX064G[6] One source | Same pitch, gauge and link count; its maker does not list this saw |
Other saws that take a chain with .325" pitch, .050" gauge, 64 drive links
Show the evidence for this row
- Pitch:
15 | 0.325 | 0.050 | 10T | 64
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.050 block (first of its gauge), row 15 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Pitch:
15 | 0.325 | 0.050 | 10T | 64
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.050 block (first of its gauge), row 15 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Pitch:
15 | 0.325 | 0.050 | 10T | Husqvarna H30 | 64
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/FR/ES), 1155359-49 Rev.4, 2017-05-03, p. 32, "Guide bar and saw chain combinations" table (models 445 II, 445e II, 450 II, 450e II), 0.050 block, row 15 (cells joined with |) - Gauge:
15 | 0.325 | 0.050 | 10T | 64
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.050 block (first of its gauge), row 15 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Gauge:
15 | 0.325 | 0.050 | 10T | 64
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.050 block (first of its gauge), row 15 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Gauge:
15 | 0.325 | 0.050 | 10T | Husqvarna H30 | 64
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/FR/ES), 1155359-49 Rev.4, 2017-05-03, p. 32, "Guide bar and saw chain combinations" table (models 445 II, 445e II, 450 II, 450e II), 0.050 block, row 15 (cells joined with |) - Drive links:
15 | 0.325 | 0.050 | 10T | 64
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.050 block (first of its gauge), row 15 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Drive links:
15 | 0.325 | 0.050 | 10T | 64
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.050 block (first of its gauge), row 15 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Drive links:
15 | 0.325 | 0.050 | 10T | Husqvarna H30 | 64
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/FR/ES), 1155359-49 Rev.4, 2017-05-03, p. 32, "Guide bar and saw chain combinations" table (models 445 II, 445e II, 450 II, 450e II), 0.050 block, row 15 (cells joined with |) - Oregon part number:
Oregon 20LPX PowerCut Saw Chain for 15 in. Bar - 64 Drive Links, Fits Echo, Makita and Dolmar | Part# 20LPX064G
— Oregon Tool, Inc., Oregon 20LPX064G product page (specifications and Fit Guide), Product heading and Part#; Product Details: ".325 Inch Pitch, .050 Inch (1.3 mm) gauge, 64 drive links"; the page's Fit Guide does not list this Husqvarna model
15-inch bar — .058" (1.5 mm) bar
.325" pitch, .058" gauge, 64 drive links One source
| Chain | Part number | Why it is listed |
|---|---|---|
| Oregon ControlCut 21BPX | 21BPX064G[17] One source | Oregon lists it for this saw |
Show the evidence for this row
- Pitch:
15 | 0.325 | 0.058 | 10T | 64
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.058 block (first of its gauge), row 15 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Pitch:
15 | 0.325 | 0.058 | 10T | 64
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.058 block (first of its gauge), row 15 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Pitch:
15 | 0.325 | 0.058 | 10T | Husqvarna H25 | 64
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/FR/ES), 1155359-49 Rev.4, 2017-05-03, p. 32, "Guide bar and saw chain combinations" table (models 445 II, 445e II, 450 II, 450e II), 0.058 block, row 15 (cells joined with |) - Gauge:
15 | 0.325 | 0.058 | 10T | 64
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.058 block (first of its gauge), row 15 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Gauge:
15 | 0.325 | 0.058 | 10T | 64
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.058 block (first of its gauge), row 15 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Gauge:
15 | 0.325 | 0.058 | 10T | Husqvarna H25 | 64
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/FR/ES), 1155359-49 Rev.4, 2017-05-03, p. 32, "Guide bar and saw chain combinations" table (models 445 II, 445e II, 450 II, 450e II), 0.058 block, row 15 (cells joined with |) - Drive links:
15 | 0.325 | 0.058 | 10T | 64
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.058 block (first of its gauge), row 15 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Drive links:
15 | 0.325 | 0.058 | 10T | 64
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.058 block (first of its gauge), row 15 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Drive links:
15 | 0.325 | 0.058 | 10T | Husqvarna H25 | 64
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/FR/ES), 1155359-49 Rev.4, 2017-05-03, p. 32, "Guide bar and saw chain combinations" table (models 445 II, 445e II, 450 II, 450e II), 0.058 block, row 15 (cells joined with |) - Oregon part number:
ControlCut™ Saw Chain, 15" | Part# 21BPX064G
— Oregon Tool, Inc., Oregon 21BPX064G product page (specifications and Fit Guide), Product heading and Part#; Product Details: "Pitch: .325", gauge: .058", drive link count: 64"; the page's Fit Guide lists Husqvarna "450" (the list is per chain family, not per loop length)
16-inch bar — .050" (1.3 mm) bar
.325" pitch, .050" gauge, 66 drive links One source
| Chain | Part number | Why it is listed |
|---|---|---|
| Husqvarna X-Cut SP33G | 581 64 36-66[4] One source | The saw maker’s own chain |
| Husqvarna X-Cut SP33G (retail pack) | 581 64 36-02[4] One source | The saw maker’s own chain |
| Husqvarna H22 | 591 09 48-66[7] One source | The saw maker’s own chain |
| Oregon SpeedCut 95TXL | 95TXL066G[8] One source | Oregon lists it for this saw |
| Oregon ControlCut 20BPX | 20BPX066G[9] One source | Oregon lists it for this saw |
Other saws that take a chain with .325" pitch, .050" gauge, 66 drive links
Show the evidence for this row
- Pitch:
16 | 0.325 | 0.050 | 10T | 66
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.050 block (first of its gauge), row 16 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Pitch:
16 | 0.325 | 0.050 | 10T | 66
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.050 block (first of its gauge), row 16 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Pitch:
16 | 0.325 | 0.050 | 10T | Husqvarna H30 | 66
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/FR/ES), 1155359-49 Rev.4, 2017-05-03, p. 32, "Guide bar and saw chain combinations" table (models 445 II, 445e II, 450 II, 450e II), 0.050 block, row 16 (cells joined with |) - Gauge:
16 | 0.325 | 0.050 | 10T | 66
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.050 block (first of its gauge), row 16 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Gauge:
16 | 0.325 | 0.050 | 10T | 66
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.050 block (first of its gauge), row 16 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Gauge:
16 | 0.325 | 0.050 | 10T | Husqvarna H30 | 66
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/FR/ES), 1155359-49 Rev.4, 2017-05-03, p. 32, "Guide bar and saw chain combinations" table (models 445 II, 445e II, 450 II, 450e II), 0.050 block, row 16 (cells joined with |) - Drive links:
16 | 0.325 | 0.050 | 10T | 66
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.050 block (first of its gauge), row 16 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Drive links:
16 | 0.325 | 0.050 | 10T | 66
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.050 block (first of its gauge), row 16 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Drive links:
16 | 0.325 | 0.050 | 10T | Husqvarna H30 | 66
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/FR/ES), 1155359-49 Rev.4, 2017-05-03, p. 32, "Guide bar and saw chain combinations" table (models 445 II, 445e II, 450 II, 450e II), 0.050 block, row 16 (cells joined with |) - Drive links:
16" / 66DL | Gauge | .050" | Bar length (inch) | 16 in | Bar length | 40 cm | Drive links | 66 | SKU: 581 64 36-66
— Husqvarna, X-CUT SP33G, .325" pitch, .050 gauge: chain product page (US), Product Options, variant row for SKU 581 64 36-66; the page's "Fits To Model" list includes 450 - Drive links:
16" / 66DL | Bar length (inch) | 16 in | Bar length | 40 cm | Gauge | .050" | SKU: 596 19 97-66
— Husqvarna, X-FORCE Laminate Sprocket Nose, .325" pitch, .050 gauge, small mount (XF-250): bar product page (US), Product Options, variant row for SKU 596 19 97-66; the page's "Fits To Model" list includes 450 - Husqvarna part number:
16" / 66DL | Gauge | .050" | Bar length (inch) | 16 in | Bar length | 40 cm | Drive links | 66 | SKU: 581 64 36-66
— Husqvarna, X-CUT SP33G, .325" pitch, .050 gauge: chain product page (US), Product Options, variant row for SKU 581 64 36-66; the page's "Fits To Model" list includes 450 - Husqvarna part number:
16" / 66DL Retail | Gauge | .050" | Bar length (inch) | 16 in | Bar length | 40 cm | Drive links | 66 | SKU: 581 64 36-02
— Husqvarna, X-CUT SP33G, .325" pitch, .050 gauge: chain product page (US), Product Options, variant row for SKU 581 64 36-02; the page's "Fits To Model" list includes 450 - Husqvarna part number:
66DL / 16", US/CA | Gauge | .050" | Bar length (inch) | 16 in | Bar length | 40 cm | Drive links | 66 | SKU: 591 09 48-66
— Husqvarna, H22, .325" pitch, .050 gauge: chain product page (US), Product Options, variant row for SKU 591 09 48-66; the page has no "Fits To Model" list, but the 2024 operator's manual table lists this chain type for the 450 Rancher - Oregon part number:
Oregon 95TXL SpeedCut Saw Chain for 16 in. Bar - 66 Drive Links - fits Echo, Husqvarna and Jonsered, Craftsman, Makita and others | Part# 95TXL066G
— Oregon Tool, Inc., Oregon 95TXL066G product page (specifications and Fit Guide), Product heading and Part#; Product Details: ".325 Inch narrow kerf Pitch, .050 Inch (1.3 mm) gauge, 66 drive links"; the page's Fit Guide lists Husqvarna "450" (the list is per chain family, not per loop length) - Oregon part number:
Oregon 20BPX ControlCut Saw Chain for 16 in. Bar - 66 Drive Links - fits Echo, Homelite, McCulloch, Makita,Jonsered Ryobi and others | Part# 20BPX066G
— Oregon Tool, Inc., Oregon 20BPX066G product page (specifications and Fit Guide), Product heading and Part#; Product Details: ".325 Inch Pitch, .050 Inch (1.3 mm) gauge, 66 drive links"; the page's Fit Guide lists Husqvarna "450" (the list is per chain family, not per loop length)
16-inch bar — .058" (1.5 mm) bar
.325" pitch, .058" gauge, 66 drive links One source
| Chain | Part number | Why it is listed |
|---|---|---|
| Husqvarna X-Cut S35G | 585 63 96-66[18] One source | The saw maker’s own chain |
| Oregon PowerCut 21LPX | 21LPX066G[19] One source | Oregon lists it for this saw |
Show the evidence for this row
- Pitch:
16 | 0.325 | 0.058 | 10T | 66
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.058 block (first of its gauge), row 16 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Pitch:
16 | 0.325 | 0.058 | 10T | 66
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.058 block (first of its gauge), row 16 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Pitch:
16 | 0.325 | 0.058 | 10T | Husqvarna H25 | 66
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/FR/ES), 1155359-49 Rev.4, 2017-05-03, p. 32, "Guide bar and saw chain combinations" table (models 445 II, 445e II, 450 II, 450e II), 0.058 block, row 16 (cells joined with |) - Gauge:
16 | 0.325 | 0.058 | 10T | 66
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.058 block (first of its gauge), row 16 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Gauge:
16 | 0.325 | 0.058 | 10T | 66
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.058 block (first of its gauge), row 16 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Gauge:
16 | 0.325 | 0.058 | 10T | Husqvarna H25 | 66
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/FR/ES), 1155359-49 Rev.4, 2017-05-03, p. 32, "Guide bar and saw chain combinations" table (models 445 II, 445e II, 450 II, 450e II), 0.058 block, row 16 (cells joined with |) - Drive links:
16 | 0.325 | 0.058 | 10T | 66
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.058 block (first of its gauge), row 16 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Drive links:
16 | 0.325 | 0.058 | 10T | 66
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.058 block (first of its gauge), row 16 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Drive links:
16 | 0.325 | 0.058 | 10T | Husqvarna H25 | 66
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/FR/ES), 1155359-49 Rev.4, 2017-05-03, p. 32, "Guide bar and saw chain combinations" table (models 445 II, 445e II, 450 II, 450e II), 0.058 block, row 16 (cells joined with |) - Husqvarna part number:
16" / 66DL | Gauge | .058" | Bar length (inch) | 16 in | Bar length | 40 cm | Drive links | 66 | SKU: 585 63 96-66
— Husqvarna, X-CUT S35G, .325" pitch, .058 gauge: chain product page (US), Product Options, variant row for SKU 585 63 96-66; this page's "Fits To Model" list does not name the saw, but the 2024 operator's manual table lists this chain type for the 450 Rancher - Oregon part number:
Oregon 21LPX PowerCut Saw Chain for 16 in. Bar - 66 Drive Links - fits Husqvarna, Poulan, Makita, Jonsered and others | Part# 21LPX066G
— Oregon Tool, Inc., Oregon 21LPX066G product page (specifications and Fit Guide), Product heading and Part#; Product Details: ".325 Inch Pitch, .058 Inch (1.5 mm) gauge, 66 drive links"; the page's Fit Guide lists Husqvarna "450" (the list is per chain family, not per loop length)
18-inch bar — .050" (1.3 mm) bar
.325" pitch, .050" gauge, 72 drive links One source
| Chain | Part number | Why it is listed |
|---|---|---|
| Husqvarna X-Cut SP33G | 581 64 36-72[4] One source | The saw maker’s own chain |
| Husqvarna X-Cut SP33G (retail pack) | 581 64 36-03[4] One source | The saw maker’s own chain |
| Husqvarna H22 | 591 09 48-72[7] One source | The saw maker’s own chain |
| Oregon SpeedCut 95TXL | 95TXL072G[11] One source | Oregon lists it for this saw |
| Oregon ControlCut 20BPX | 20BPX072G[12] One source | Oregon lists it for this saw |
Other saws that take a chain with .325" pitch, .050" gauge, 72 drive links
Show the evidence for this row
- Pitch:
18 | 0.325 | 0.050 | 10T | 72
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.050 block (first of its gauge), row 18 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Pitch:
18 | 0.325 | 0.050 | 10T | 72
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.050 block (first of its gauge), row 18 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Pitch:
18 | 0.325 | 0.050 | 10T | Husqvarna H30 | 72
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/FR/ES), 1155359-49 Rev.4, 2017-05-03, p. 32, "Guide bar and saw chain combinations" table (models 445 II, 445e II, 450 II, 450e II), 0.050 block, row 18 (cells joined with |) - Pitch:
Pitch | .325" | Chain type | H30 | Bar length | 45 cm | Bar length (inch) | 18 in | 18" Bar, .325" Pitch, .050" Gauge | 965 14 67-01
— Husqvarna, Parts, manuals and support for 450 (US support page; the 450 Rancher product address redirects here), Specifications > Equipment, article 965 14 67-01 - Gauge:
18 | 0.325 | 0.050 | 10T | 72
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.050 block (first of its gauge), row 18 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Gauge:
18 | 0.325 | 0.050 | 10T | 72
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.050 block (first of its gauge), row 18 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Gauge:
18 | 0.325 | 0.050 | 10T | Husqvarna H30 | 72
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/FR/ES), 1155359-49 Rev.4, 2017-05-03, p. 32, "Guide bar and saw chain combinations" table (models 445 II, 445e II, 450 II, 450e II), 0.050 block, row 18 (cells joined with |) - Drive links:
18 | 0.325 | 0.050 | 10T | 72
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.050 block (first of its gauge), row 18 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Drive links:
18 | 0.325 | 0.050 | 10T | 72
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.050 block (first of its gauge), row 18 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Drive links:
18 | 0.325 | 0.050 | 10T | Husqvarna H30 | 72
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/FR/ES), 1155359-49 Rev.4, 2017-05-03, p. 32, "Guide bar and saw chain combinations" table (models 445 II, 445e II, 450 II, 450e II), 0.050 block, row 18 (cells joined with |) - Drive links:
18" / 72DL | Gauge | .050" | Bar length (inch) | 18 in | Bar length | 45 cm | Drive links | 72 | SKU: 581 64 36-72
— Husqvarna, X-CUT SP33G, .325" pitch, .050 gauge: chain product page (US), Product Options, variant row for SKU 581 64 36-72; the page's "Fits To Model" list includes 450 - Drive links:
18" / 72DL | Bar length (inch) | 18 in | Bar length | 45 cm | Gauge | .050" | SKU: 596 19 97-72
— Husqvarna, X-FORCE Laminate Sprocket Nose, .325" pitch, .050 gauge, small mount (XF-250): bar product page (US), Product Options, variant row for SKU 596 19 97-72; the page's "Fits To Model" list includes 450 - Husqvarna part number:
18" / 72DL | Gauge | .050" | Bar length (inch) | 18 in | Bar length | 45 cm | Drive links | 72 | SKU: 581 64 36-72
— Husqvarna, X-CUT SP33G, .325" pitch, .050 gauge: chain product page (US), Product Options, variant row for SKU 581 64 36-72; the page's "Fits To Model" list includes 450 - Husqvarna part number:
18" / 72DL Retail | Gauge | .050" | Bar length (inch) | 18 in | Bar length | 45 cm | Drive links | 72 | SKU: 581 64 36-03
— Husqvarna, X-CUT SP33G, .325" pitch, .050 gauge: chain product page (US), Product Options, variant row for SKU 581 64 36-03; the page's "Fits To Model" list includes 450 - Husqvarna part number:
72DL / 18", US/CA | Gauge | .050" | Bar length (inch) | 18 in | Bar length | 45 cm | Drive links | 72 | SKU: 591 09 48-72
— Husqvarna, H22, .325" pitch, .050 gauge: chain product page (US), Product Options, variant row for SKU 591 09 48-72; the page has no "Fits To Model" list, but the 2024 operator's manual table lists this chain type for the 450 Rancher - Oregon part number:
Oregon 95TXL SpeedCut Chainsaw Chain for 18-Inch Bar -72 Drive Links – fits Husqvarna, Dolmar, Jonsered and more | Part# 95TXL072G
— Oregon Tool, Inc., Oregon 95TXL072G product page (specifications and Fit Guide), Product heading and Part#; Product Details: ".325 Inch narrow kerf Pitch, .050 Inch (1.3 mm) gauge, 72 drive links"; the page's Fit Guide lists Husqvarna "450" (the list is per chain family, not per loop length) - Oregon part number:
Oregon 20BPX ControlCut Saw Chain for 18 in. Bar - 72 Drive Links - fits Echo, Craftsman, Homelite, Poulan, Husqvarna, Makita and others | Part# 20BPX072G
— Oregon Tool, Inc., Oregon 20BPX072G product page (specifications and Fit Guide), Product heading and Part#; Product Details: ".325 Inch Pitch, .050 Inch (1.3 mm) gauge, 72 drive links"; the page's Fit Guide lists Husqvarna "450" (the list is per chain family, not per loop length)
18-inch bar — .058" (1.5 mm) bar
.325" pitch, .058" gauge, 72 drive links One source
| Chain | Part number | Why it is listed |
|---|---|---|
| Husqvarna X-Cut S35G | 585 63 96-72[18] One source | The saw maker’s own chain |
| Oregon ControlCut 21BPX | 21BPX072G[20] One source | Oregon lists it for this saw |
| Oregon PowerCut 21LPX | 21LPX072G[21] One source | Oregon lists it for this saw |
Show the evidence for this row
- Pitch:
18 | 0.325 | 0.058 | 10T | 72
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.058 block (first of its gauge), row 18 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Pitch:
18 | 0.325 | 0.058 | 10T | 72
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.058 block (first of its gauge), row 18 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Pitch:
18 | 0.325 | 0.058 | 10T | Husqvarna H25 | 72
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/FR/ES), 1155359-49 Rev.4, 2017-05-03, p. 32, "Guide bar and saw chain combinations" table (models 445 II, 445e II, 450 II, 450e II), 0.058 block, row 18 (cells joined with |) - Gauge:
18 | 0.325 | 0.058 | 10T | 72
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.058 block (first of its gauge), row 18 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Gauge:
18 | 0.325 | 0.058 | 10T | 72
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.058 block (first of its gauge), row 18 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Gauge:
18 | 0.325 | 0.058 | 10T | Husqvarna H25 | 72
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/FR/ES), 1155359-49 Rev.4, 2017-05-03, p. 32, "Guide bar and saw chain combinations" table (models 445 II, 445e II, 450 II, 450e II), 0.058 block, row 18 (cells joined with |) - Drive links:
18 | 0.325 | 0.058 | 10T | 72
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.058 block (first of its gauge), row 18 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Drive links:
18 | 0.325 | 0.058 | 10T | 72
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.058 block (first of its gauge), row 18 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Drive links:
18 | 0.325 | 0.058 | 10T | Husqvarna H25 | 72
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/FR/ES), 1155359-49 Rev.4, 2017-05-03, p. 32, "Guide bar and saw chain combinations" table (models 445 II, 445e II, 450 II, 450e II), 0.058 block, row 18 (cells joined with |) - Husqvarna part number:
18" / 72DL | Gauge | .058" | Bar length (inch) | 18 in | Bar length | 45 cm | Drive links | 72 | SKU: 585 63 96-72
— Husqvarna, X-CUT S35G, .325" pitch, .058 gauge: chain product page (US), Product Options, variant row for SKU 585 63 96-72; this page's "Fits To Model" list does not name the saw, but the 2024 operator's manual table lists this chain type for the 450 Rancher - Oregon part number:
Oregon 21BPX ControlCut Saw Chain for 18 in. Bar - 72 Drive Links - fits Husqvarna, Jonsered, Makita, Poulan and others | Part# 21BPX072G
— Oregon Tool, Inc., Oregon 21BPX072G product page (specifications and Fit Guide), Product heading and Part#; Product Details: ".325 Inch Pitch, .058 Inch (1.5 mm) gauge, 72 drive links"; the page's Fit Guide lists Husqvarna "450" (the list is per chain family, not per loop length) - Oregon part number:
Oregon 21LPX PowerCut Saw Chain for 18 in. Bar - 72 Drive Links - fits Husqvarna, Jonsered, Makita, Poulan and others | Part# 21LPX072G
— Oregon Tool, Inc., Oregon 21LPX072G product page (specifications and Fit Guide), Product heading and Part#; Product Details: ".325 Inch Pitch, .058 Inch (1.5 mm) gauge, 72 drive links"; the page's Fit Guide lists Husqvarna "450" (the list is per chain family, not per loop length)
20-inch bar — .050" (1.3 mm) bar; 20 inch bar marked 78 drive links
.325" pitch, .050" gauge, 78 drive links One source
| Chain | Part number | Why it is listed |
|---|---|---|
| Husqvarna X-Cut SP33G | 581 64 36-78[4] One source | The saw maker’s own chain |
| Husqvarna H22 | 591 09 48-78[7] One source | The saw maker’s own chain |
| Oregon ControlCut 20BPX | 20BPX078G[13] One source | Oregon lists it for this saw |
| Oregon PowerCut 20LPX | 20LPX078G[14] One source | Oregon lists it for this saw |
Show the evidence for this row
- Pitch:
20 | 0.325 | 0.050 | 10T | 78/80*
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.050 block (first of its gauge), row 20 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Pitch:
20 | 0.325 | 0.050 | 10T | 78/80*
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.050 block (first of its gauge), row 20 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Pitch:
20 | 0.325 | 0.050 | 10T | Husqvarna H30 | 78
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/FR/ES), 1155359-49 Rev.4, 2017-05-03, p. 32, "Guide bar and saw chain combinations" table (models 445 II, 445e II, 450 II, 450e II), 0.050 block, row 20 (cells joined with |) - Gauge:
20 | 0.325 | 0.050 | 10T | 78/80*
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.050 block (first of its gauge), row 20 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Gauge:
20 | 0.325 | 0.050 | 10T | 78/80*
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.050 block (first of its gauge), row 20 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Gauge:
20 | 0.325 | 0.050 | 10T | Husqvarna H30 | 78
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/FR/ES), 1155359-49 Rev.4, 2017-05-03, p. 32, "Guide bar and saw chain combinations" table (models 445 II, 445e II, 450 II, 450e II), 0.050 block, row 20 (cells joined with |) - Drive links:
20 | 0.325 | 0.050 | 10T | 78/80*
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.050 block (first of its gauge), row 20 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Drive links:
20 | 0.325 | 0.050 | 10T | 78/80*
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.050 block (first of its gauge), row 20 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Drive links:
20 | 0.325 | 0.050 | 10T | Husqvarna H30 | 78
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/FR/ES), 1155359-49 Rev.4, 2017-05-03, p. 32, "Guide bar and saw chain combinations" table (models 445 II, 445e II, 450 II, 450e II), 0.050 block, row 20 (cells joined with |) - Drive links:
20" / 78DL | Gauge | .050" | Bar length (inch) | 20 in | Bar length | 50 cm | Drive links | 78 | SKU: 581 64 36-78
— Husqvarna, X-CUT SP33G, .325" pitch, .050 gauge: chain product page (US), Product Options, variant row for SKU 581 64 36-78; the page's "Fits To Model" list includes 450 - Husqvarna part number:
20" / 78DL | Gauge | .050" | Bar length (inch) | 20 in | Bar length | 50 cm | Drive links | 78 | SKU: 581 64 36-78
— Husqvarna, X-CUT SP33G, .325" pitch, .050 gauge: chain product page (US), Product Options, variant row for SKU 581 64 36-78; the page's "Fits To Model" list includes 450 - Husqvarna part number:
78DL / 20", US/CA | Gauge | .050" | Bar length (inch) | 20 in | Bar length | 50 cm | Drive links | 78 | SKU: 591 09 48-78
— Husqvarna, H22, .325" pitch, .050 gauge: chain product page (US), Product Options, variant row for SKU 591 09 48-78; the page has no "Fits To Model" list, but the 2024 operator's manual table lists this chain type for the 450 Rancher - Oregon part number:
Oregon 20BPX ControlCut Saw Chain for 20 in. Bar - 78 Drive Links - fits Husqvarna, Jonsered and More | Part# 20BPX078G
— Oregon Tool, Inc., Oregon 20BPX078G product page (specifications and Fit Guide), Product heading and Part#; Product Details: ".325 Inch Pitch, .050 Inch (1.3 mm) gauge, 78 drive links"; the page's Fit Guide lists Husqvarna "450" (the list is per chain family, not per loop length) - Oregon part number:
Oregon 20LPX PowerCut Saw Chain for 20 in. Bar - 78 Drive Links - fits Husqvarna, Jonsered and More | Part# 20LPX078G
— Oregon Tool, Inc., Oregon 20LPX078G product page (specifications and Fit Guide), Product heading and Part#; Product Details: ".325 Inch Pitch, .050 Inch (1.3 mm) gauge, 78 drive links"; the page's Fit Guide lists Husqvarna "450" (the list is per chain family, not per loop length)
20-inch bar — .050" (1.3 mm) bar; 20 inch bar marked 80 drive links
.325" pitch, .050" gauge, 80 drive links One source
| Chain | Part number | Why it is listed |
|---|---|---|
| Husqvarna X-Cut SP33G | 581 64 36-80[4] One source | The saw maker’s own chain |
| Husqvarna X-Cut SP33G (retail pack) | 581 64 36-04[4] One source | The saw maker’s own chain |
| Oregon PowerCut 20LPX | 20LPX080G[15] One source | Same pitch, gauge and link count; its maker does not list this saw |
Show the evidence for this row
- Pitch:
20 | 0.325 | 0.050 | 10T | 78/80*
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.050 block (first of its gauge), row 20 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Pitch:
20 | 0.325 | 0.050 | 10T | 78/80*
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.050 block (first of its gauge), row 20 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Gauge:
20 | 0.325 | 0.050 | 10T | 78/80*
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.050 block (first of its gauge), row 20 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Gauge:
20 | 0.325 | 0.050 | 10T | 78/80*
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.050 block (first of its gauge), row 20 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Drive links:
20 | 0.325 | 0.050 | 10T | 78/80*
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.050 block (first of its gauge), row 20 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Drive links:
20 | 0.325 | 0.050 | 10T | 78/80*
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.050 block (first of its gauge), row 20 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Drive links:
20" / 80DL | Gauge | .050" | Bar length (inch) | 20 in | Bar length | 50 cm | Drive links | 80 | SKU: 581 64 36-80
— Husqvarna, X-CUT SP33G, .325" pitch, .050 gauge: chain product page (US), Product Options, variant row for SKU 581 64 36-80; the page's "Fits To Model" list includes 450 - Drive links:
20" / 80DL | Bar length (inch) | 20 in | Bar length | 50 cm | Gauge | .050" | SKU: 596 19 97-80
— Husqvarna, X-FORCE Laminate Sprocket Nose, .325" pitch, .050 gauge, small mount (XF-250): bar product page (US), Product Options, variant row for SKU 596 19 97-80; the page's "Fits To Model" list includes 450 - Husqvarna part number:
20" / 80DL | Gauge | .050" | Bar length (inch) | 20 in | Bar length | 50 cm | Drive links | 80 | SKU: 581 64 36-80
— Husqvarna, X-CUT SP33G, .325" pitch, .050 gauge: chain product page (US), Product Options, variant row for SKU 581 64 36-80; the page's "Fits To Model" list includes 450 - Husqvarna part number:
20" / 80DL Retail | Gauge | .050" | Bar length (inch) | 20 in | Bar length | 50 cm | Drive links | 80 | SKU: 581 64 36-04
— Husqvarna, X-CUT SP33G, .325" pitch, .050 gauge: chain product page (US), Product Options, variant row for SKU 581 64 36-04; the page's "Fits To Model" list includes 450 - Oregon part number:
Oregon 20LPX PowerCut Saw Chain for 20 in. Bar - 80 Drive Links, Fits Ryobi | Part# 20LPX080G
— Oregon Tool, Inc., Oregon 20LPX080G product page (specifications and Fit Guide), Product heading and Part#; Product Details: ".325 Inch Pitch, .050 Inch (1.3 mm) gauge, 80 drive links"; the page's Fit Guide does not list this Husqvarna model
20-inch bar — .058" (1.5 mm) bar; 20 inch bar marked 78 drive links
.325" pitch, .058" gauge, 78 drive links One source
| Chain | Part number | Why it is listed |
|---|---|---|
| Husqvarna X-Cut S35G | 585 63 96-78[18] One source | The saw maker’s own chain |
| Oregon ControlCut 21BPX | 21BPX078G[22] One source | Oregon lists it for this saw |
| Oregon PowerCut 21LPX | 21LPX078G[23] One source | Oregon lists it for this saw |
Show the evidence for this row
- Pitch:
20 | 0.325 | 0.058 | 12T | 78/80*
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.058 block (first of its gauge), row 20 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Pitch:
20 | 0.325 | 0.058 | 12T | 78/80*
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.058 block (first of its gauge), row 20 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Pitch:
20 | 0.325 | 0.058 | 12T | Husqvarna H25 | 78
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/FR/ES), 1155359-49 Rev.4, 2017-05-03, p. 32, "Guide bar and saw chain combinations" table (models 445 II, 445e II, 450 II, 450e II), 0.058 block, row 20 (cells joined with |) - Gauge:
20 | 0.325 | 0.058 | 12T | 78/80*
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.058 block (first of its gauge), row 20 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Gauge:
20 | 0.325 | 0.058 | 12T | 78/80*
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.058 block (first of its gauge), row 20 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Gauge:
20 | 0.325 | 0.058 | 12T | Husqvarna H25 | 78
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/FR/ES), 1155359-49 Rev.4, 2017-05-03, p. 32, "Guide bar and saw chain combinations" table (models 445 II, 445e II, 450 II, 450e II), 0.058 block, row 20 (cells joined with |) - Drive links:
20 | 0.325 | 0.058 | 12T | 78/80*
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.058 block (first of its gauge), row 20 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Drive links:
20 | 0.325 | 0.058 | 12T | 78/80*
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.058 block (first of its gauge), row 20 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Drive links:
20 | 0.325 | 0.058 | 12T | Husqvarna H25 | 78
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/FR/ES), 1155359-49 Rev.4, 2017-05-03, p. 32, "Guide bar and saw chain combinations" table (models 445 II, 445e II, 450 II, 450e II), 0.058 block, row 20 (cells joined with |) - Husqvarna part number:
20" / 78DL | Gauge | .058" | Bar length (inch) | 20 in | Bar length | 50 cm | Drive links | 78 | SKU: 585 63 96-78
— Husqvarna, X-CUT S35G, .325" pitch, .058 gauge: chain product page (US), Product Options, variant row for SKU 585 63 96-78; this page's "Fits To Model" list does not name the saw, but the 2024 operator's manual table lists this chain type for the 450 Rancher - Oregon part number:
ControlCut™ Saw Chain, 20" | Part# 21BPX078G
— Oregon Tool, Inc., Oregon 21BPX078G product page (specifications and Fit Guide), Product heading and Part#; Product Details: "Pitch: .325", gauge: .058", drive link count: 78"; the page's Fit Guide lists Husqvarna "450" (the list is per chain family, not per loop length) - Oregon part number:
Oregon 21LPX PowerCut Saw Chain for 20 in. Bar - 78 Drive Links - fits Echo, Husqvarna, Makita, Poulan, Jonsered and others | Part# 21LPX078G
— Oregon Tool, Inc., Oregon 21LPX078G product page (specifications and Fit Guide), Product heading and Part#; Product Details: ".325 Inch Pitch, .058 Inch (1.5 mm) gauge, 78 drive links"; the page's Fit Guide lists Husqvarna "450" (the list is per chain family, not per loop length)
20-inch bar — .058" (1.5 mm) bar; 20 inch bar marked 80 drive links
.325" pitch, .058" gauge, 80 drive links One source
Search for .325 .058 80 drive link chainsaw chain: Amazon.com (paid link) Amazon.caShow the evidence for this row
- Pitch:
20 | 0.325 | 0.058 | 12T | 78/80*
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.058 block (first of its gauge), row 20 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Pitch:
20 | 0.325 | 0.058 | 12T | 78/80*
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.058 block (first of its gauge), row 20 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Gauge:
20 | 0.325 | 0.058 | 12T | 78/80*
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.058 block (first of its gauge), row 20 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Gauge:
20 | 0.325 | 0.058 | 12T | 78/80*
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.058 block (first of its gauge), row 20 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Drive links:
20 | 0.325 | 0.058 | 12T | 78/80*
— Husqvarna, Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024, p. 35, "Recommended cutting equipment" table, 0.058 block (first of its gauge), row 20 (cells joined with |: length, pitch, gauge, max. nose radius, drive links) - Drive links:
20 | 0.325 | 0.058 | 12T | 78/80*
— Husqvarna, Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020, p. 28, "Recommended cutting equipment" table (models 445 II, 445e II, 450 II, 450e II), 0.058 block (first of its gauge), row 20 (cells joined with |: length, pitch, gauge, max. nose radius, drive links)
Confirm before you order
- Read the bar. Most bars have the pitch, gauge and drive-link count stamped near the mounting end. Those numbers describe the bar actually on your saw, which may not be the one it left the factory with.
- If the stamp is worn off, count the drive links on the old chain: the teeth on the inside of the loop that ride in the bar groove.
- Match all three numbers to one row of the Husqvarna 450 Rancher table above. A chain with the right length but the wrong gauge or pitch will not fit the bar or the sprocket.
How to find pitch, gauge and drive links step by step
If your saw matches none of the rows, its bar or sprocket has probably been changed. Go by what is stamped on the bar, or ask a dealer.
20 inch bars: 78 or 80 links
The 2017 North American manual (445 II, 450 II) lists 78 links for the 20 inch bar. The 2020 and 2024 editions list 78/80 with a footnote that two different drive link counts exist for 20 inch bars and that the information on the guide bar should be checked. Husqvarna's X-Force .325 .050 bar page, which names the 450, sells the 20 inch bar as 80DL; its SP33G page sells both 78 and 80 link loops; and the Oregon 20 inch .325 loops that name Husqvarna are 78 link loops.
No document opened for this record ties either count to a production date, so the marking on the bar is the only reliable guide.
Two gauges
The current manual gives drive link thickness as 0.058/1.5, 0.050/1.3 and lists SP33G, H30 and H22 at .050 and H25 and S35G at .058. The 2017 manual says the owner is free to choose either gauge for the corresponding bar. Husqvarna's US support page shows the saw with an 18 inch, .325, .050 bar and H30 chain.
Model names
Husqvarna's US site redirects the 450 Rancher product address to a support page titled 450 and marked discontinued. The 2024 manual is titled 445, 450 Rancher; the 2017 and 2020 editions call the saw 450 II and 450e II. Oregon lists it as 450.
Chains without a row here
H30 and H25 are named in the manuals, but no Husqvarna page opened for this record gave loop part numbers for them. Husqvarna's S35G page gives .058 loops without naming the 450 in its own fit list; the 2024 manual table does list S35G for this saw. None of the Husqvarna or Oregon pages opened lists an 80 link .058 loop.
How Oregon equivalents were matched
Oregon's product pages carry a fit list for each chain, but the list is the same for every loop length of a chain family. The drive-link counts in this record therefore come from Husqvarna's documents; Oregon's pages are used only for the Oregon part number and for whether Oregon names this saw.
Sources
- Husqvarna. Operator's manual: 445, 450 Rancher (EN/ES/FR), publication 1286-014, 30.01.2024. Saw maker’s own document; retrieved November 18, 2026
- Husqvarna. Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/FR/ES), 1155359-49 Rev.4, 2017-05-03. Saw maker’s own document; retrieved November 18, 2026
- Husqvarna. Operator's manual: 445 II, 445e II, 450 II, 450e II (EN/ES-MX/FR-CA), publication 1286-003, 30.06.2020. Saw maker’s own document; retrieved November 18, 2026
- Husqvarna. X-CUT SP33G, .325" pitch, .050 gauge: chain product page (US). Saw maker’s own document; retrieved November 18, 2026
- Husqvarna. X-FORCE Laminate Sprocket Nose, .325" pitch, .050 gauge, small mount (XF-250): bar product page (US). Saw maker’s own document; retrieved November 18, 2026
- Oregon Tool, Inc. Oregon 20LPX064G product page (specifications and Fit Guide). Chain or bar maker’s fit data; retrieved November 18, 2026
- Husqvarna. H22, .325" pitch, .050 gauge: chain product page (US). Saw maker’s own document; retrieved November 18, 2026
- Oregon Tool, Inc. Oregon 95TXL066G product page (specifications and Fit Guide). Chain or bar maker’s fit data; retrieved November 18, 2026
- Oregon Tool, Inc. Oregon 20BPX066G product page (specifications and Fit Guide). Chain or bar maker’s fit data; retrieved November 18, 2026
- Husqvarna. Parts, manuals and support for 450 (US support page; the 450 Rancher product address redirects here). Saw maker’s own document; retrieved November 18, 2026
- Oregon Tool, Inc. Oregon 95TXL072G product page (specifications and Fit Guide). Chain or bar maker’s fit data; retrieved November 18, 2026
- Oregon Tool, Inc. Oregon 20BPX072G product page (specifications and Fit Guide). Chain or bar maker’s fit data; retrieved November 18, 2026
- Oregon Tool, Inc. Oregon 20BPX078G product page (specifications and Fit Guide). Chain or bar maker’s fit data; retrieved November 18, 2026
- Oregon Tool, Inc. Oregon 20LPX078G product page (specifications and Fit Guide). Chain or bar maker’s fit data; retrieved November 18, 2026
- Oregon Tool, Inc. Oregon 20LPX080G product page (specifications and Fit Guide). Chain or bar maker’s fit data; retrieved November 18, 2026
- Oregon Tool, Inc. Oregon 21BPX056G product page (specifications and Fit Guide). Chain or bar maker’s fit data; retrieved November 18, 2026
- Oregon Tool, Inc. Oregon 21BPX064G product page (specifications and Fit Guide). Chain or bar maker’s fit data; retrieved November 18, 2026
- Husqvarna. X-CUT S35G, .325" pitch, .058 gauge: chain product page (US). Saw maker’s own document; retrieved November 18, 2026
- Oregon Tool, Inc. Oregon 21LPX066G product page (specifications and Fit Guide). Chain or bar maker’s fit data; retrieved November 18, 2026
- Oregon Tool, Inc. Oregon 21BPX072G product page (specifications and Fit Guide). Chain or bar maker’s fit data; retrieved November 18, 2026
- Oregon Tool, Inc. Oregon 21LPX072G product page (specifications and Fit Guide). Chain or bar maker’s fit data; retrieved November 18, 2026
- Oregon Tool, Inc. Oregon 21BPX078G product page (specifications and Fit Guide). Chain or bar maker’s fit data; retrieved November 18, 2026
- Oregon Tool, Inc. Oregon 21LPX078G product page (specifications and Fit Guide). Chain or bar maker’s fit data; retrieved November 18, 2026
Seen a number here that does not match your saw or its manual? Report it.