Chain types, file sizes and filing angles
Links marked “(paid link)” go to Amazon and earn this site a commission if you buy. As an Amazon Associate I earn from qualifying purchases. How this works
Two chains of the same pitch, gauge and length can still differ in cutter shape, kerf width and kickback features. Those differences affect how the chain cuts and how you sharpen it. The file sizes and angles below are given maker by maker, because the makers do not agree on one rule.
Cutter shapes
- Full chisel. The corner where the top plate meets the side plate is square. Husqvarna says full chisel cutters give the fastest, most efficient cutting in clean softwood. Stihl, which calls this shape Super, adds that resharpening it requires more experience.
- Semi-chisel. The corner is rounded. Husqvarna says this keeps the cutter sharp for longer in hard or frozen wood and in dirty conditions. Stihl calls the shape Micro and describes it as easy to maintain and resharpen. Oregon says semi-chisel cutters are typically more tolerant of sharpening errors than chisel cutters.
- In-between shapes. Oregon lists five cutter types: chipper, semi-chisel, Chamfer Chisel, Micro Chisel and chisel. It describes Micro Chisel cutters as having small-radius working corners and Chamfer Chisel cutters as having twin cutting corners. Husqvarna describes a chipper cutter as like a semi-chisel with an even rounder corner.
Low-profile chain
Low-profile chain has a lower cutter and is made for smaller saws. Each maker has its own name for it: Oregon’s Low Profile pitches (3/8″ Low Profile and .325″ Low Profile), Stihl’s Picco chains (3/8″ P and 1/4″ P) and Husqvarna’s mini pitches. Stihl describes Picco as a low-profile cutter whose teeth sit closer to the bar. Husqvarna says its mini chains have low-profile cutters and smaller drive links. A low-profile chain is not interchangeable with the standard chain of the same fraction: Stihl states that 3/8″ and 3/8″ P are entirely different pitches.
Narrow-kerf chain
Kerf is the width of material the chain removes. A narrow-kerf chain removes less, and Oregon says such a system needs less power from the saw than a standard one. Oregon’s narrow-kerf .325″ chain is its 95 series. Husqvarna’s name is Pixel, marked by a P in X-CUT names such as SP33G. Both makers tie the chain to the bar: Oregon says to run narrow-kerf chain only on narrow-kerf bars, and Husqvarna says Pixel chain is only to be used with Pixel bars.
Low-kickback chain
Low-kickback chain has features built in to reduce kickback. Oregon names three: the bumper drive link, the ramped depth gauge and the wide-track depth gauge. Stihl uses a humped drive link and marks those chains with a 3, as in 26 RM3. Husqvarna’s G, as in SP33G, stands for a guarded drive link. None of this prevents kickback; Stihl says these chains are designed to reduce the risk of kickback injury.
In the United States the reference is ANSI B175.1. Stihl defines a low-kickback chain as one that has met the kickback performance requirements of ANSI/OPEI B175.1-2012. Oregon explains that the standard splits saws at 3.8 cubic inches (62 cc): saws below that size must meet its low-kickback provisions, larger saws may or may not. In Canada the reference is CSA Z62.3; Oregon states that its low-kickback chain meets that standard’s kickback performance requirements, and a Husqvarna operator’s manual cites CSA Z62.3-11 (Chainsaw kickback) beside ANSI B175.1-2012. Husqvarna’s manual treats compliance as a property of a combination: a saw model has to be evaluated together with its cutting equipment.
On the shelf, Oregon and Stihl both use a green label for low-kickback chain and a yellow label for chain that is not. The saw pages on this site list the chains documented for each saw, for example Echo CS-400 or Poulan Pro PR5020.
Round file sizes and angles, maker by maker
Use the table for the maker of your chain, not the maker of your saw. How to read chain numbers shows how to tell which chain you have.
Oregon
Oregon specifies by chain type. The angles are the top-plate angle, the down angle of the file and the side-plate angle.
| Oregon chain | Round file | Top plate | Down | Side plate | Depth gauge |
|---|---|---|---|---|---|
| 80TXL | 5/32″ | 25° | 10° | 70° | .025″ |
| 90PX | 4.5 mm | 30° | 0° | 75° | .025″ |
| 91P, 91PX, 91PXL, 91VXL | 5/32″ | 30° | 0° | 80° | .025″ |
| 95TXL; 20, 21, 22BPX | 3/16″ | 30° | 10° | 70° | .025″ |
| 20, 21, 22LPX and LGX | 3/16″ | 25° | 10° | 60° | .025″ |
| 72APX; 72, 73, 75DPX | 7/32″ | 30° | 10° | 80° | .025″ |
| 72, 73, 75V, EXL, LGX and LPX | 7/32″ | 25° | 10° | 60° | .025″ |
Stihl
Stihl specifies by pitch, which you read from the digit stamped on each cutter.
| Pitch | Stamp | Round file | Depth gauge setting |
|---|---|---|---|
| 1/4″ P | 7 | 3.2 mm (1/8″) | 0.45 mm (.018″) |
| 1/4″ | 1 | 4.0 mm (5/32″) | 0.65 mm (.026″) |
| 3/8″ P | 6 | 4.0 mm (5/32″) | 0.65 mm (.026″) |
| .325″ | 2 | 4.8 mm (3/16″) | 0.65 mm (.026″) |
| 3/8″ | 3 | 5.2 mm (13/64″) | 0.65 mm (.026″) |
| .404″ | 4 | 5.5 mm (7/32″) | 0.80 mm (.031″) |
Stihl sharpens its chains at a 30° sharpening angle. Ripping chains, which have an X in the name, are the exception at 10°. The side-plate angle is 75° for Micro cutters and 60° for Super cutters, and Stihl says it results automatically when the specified file holder and file diameter are used. Carbide-tipped Duro chains cannot be sharpened by hand at all.
Husqvarna
| Round file | Pitch | Chains Husqvarna names |
|---|---|---|
| 3.5 mm (9/64″) | 1/4″ mini | SP11G |
| 4.0 mm (5/32″) | 1/4″, 3/8″ mini, .325″ mini | SP21G, S93G, H00, H37 |
| 4.8 mm (3/16″) | .325″ | SP33G, S35G, C33, C35, H30, H25, H21, H23 |
| 5.5 mm (7/32″) | 3/8″, .404″ | C83, C85, S85, S83G, H42, H47, H48, H54, H80, H64 |
Husqvarna calls these common sizes and sends you to the saw’s operator’s manual for the exact figure. One such manual gives a 30° filing angle for SP33G, H30, H25 and H22, with a depth gauge setting of .030″ for SP33G and .025″ for the three H chains.
Where the makers differ
- 3/8″ chain: Oregon and Husqvarna specify 7/32″ (5.5 mm). Stihl specifies 5.2 mm (13/64″).
- 3/8″ low-profile chain: Stihl and Husqvarna specify 4.0 mm. Oregon specifies 5/32″ for its 91 series but 4.5 mm for 90PX.
- 1/4″ chain: Stihl specifies 4.0 mm for 1/4″ and 3.2 mm for 1/4″ P. Husqvarna specifies 4.0 mm for 1/4″ and 3.5 mm for its 1/4″ mini SP11G.
- Raised drive links: Oregon says not to file the tops of its bumper drive links. Stihl says the hump on its humped drive links is lowered along with the depth gauge.
Holding the file
The diameter matters because of where the file sits. Oregon says one fifth of the file’s diameter should stay above the cutter’s top plate; Stihl says one quarter. Oregon says a file guide is the easiest way to hold that position, and Stihl says its file holder keeps the file at the correct height. Both tell you to file from the inside of the cutter to the outside. Oregon’s manual says a file that is too small or held too low puts too much hook in the side plate, and Stihl lists a hooked side plate among the causes of increased kickback risk. Search for chainsaw round file and file guide: Amazon.com (paid link) Amazon.ca
Check the depth gauges after sharpening. Stihl warns that depth gauges set too low increase the saw’s tendency to kick back, and Husqvarna’s manual warns that the risk of kickback increases if the depth gauge setting is too large.
Sources
- Oregon, Saw Chain Filing and Grinding Angles (2020 chart), linked from Oregon Product Manuals.
- Oregon, Maintenance and Safety Manual: Saw Chain, Guide Bar and Drive Sprocket (A106971 rev. AC).
- Oregon, Saw Chain Anatomy & Terminology, Chainsaw Safety and Sharpening Chainsaw Chain (product support articles).
- Stihl, Sharpening STIHL Saw Chains (0457 181 0121, 2012).
- Stihl, MS 231, 251 Instruction Manual (0458-737-8321-C).
- Stihl USA, Chain Saw Safety Manual.
- Stihl UK, How to Choose The Right Saw Chain For Your Chainsaw.
- Husqvarna US Help Center, How to choose the correct file size for a chainsaw chain? (KA-01611).
- Husqvarna, Operator’s manual 445 II, 445e II, 450 II, 450e II (2021-06).
- Husqvarna UK, Choosing the right chainsaw chain type: A step-by-step guide.